Avaire Forum  

Go Back   Avaire Forum > Public Information > Floor Preparation > Floor heat

Thread: Floor heat Reply to Thread
Your Username: Click here to log in
Image Verification
Post Icons
You may choose an icon for your message from the following list:

Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-24-2009 10:53 AM
Avaire Archive Author: Jon
Date: 2/28/2009 2:15 pm EDT
Let me re-phrase that...

What I had stated was, "The following has been taken off their website" which sounds like they removed it from their website.

The information I stated was, obtained from their website.
06-24-2009 10:53 AM
Avaire Archive Author: Chris
Date: 2/27/2009 9:39 am EDT
Great research!

Sounds like you're ready to go.I still would used the Insulayment rather than Quiet walk.It's firmer and will support the tile better. Quiet Walk and Insulayment are made by the same company and use basicly the same materials for each product. I will check but I'm sure it's okay to use.
06-24-2009 10:53 AM
Avaire Archive Author: Jon
Date: 2/26/2009 7:28 pm EDT
I am not sure where I got that pad thickness of 3/8” but anyway; here is more info on the panels.
I would be using QuietWalk underlayment as it has been approved for use with these heat panels.

To ensure the temperature does not exceed 84 or 115 degrees, all I need to do is install a thermostat, right?

The following has been taken off the their website….

Environ II panels are less than 1/16” thick. The power supply cord is ¼”.

Environ II panels are made of a pattern of a fixed-resistance heating element, “sandwiched” between two layers of aluminum foil laminate.

The aluminum foil that forms the outer casing of the panel provides several advantages:
• Heat generated by the heating element wire within the panel rapidly spreads through the foil, creating a large “plate” at an even temperature.
This also helps to prevent heat build up under chair and table legs, as the natural tendency of the foil is to draw heat away from a hot spot.
• It is waterproof, thus protecting all internal wiring and connections within the panel;
• It is rigid, yet still sufficiently flexible to make for ease of installation;
06-24-2009 10:52 AM
Avaire Archive Author: Chris
Date: 2/26/2009 3:50 pm EDT
I've worked with the Warmly Yours product a few times and it's less than 1/8" tick and if a product like Insulayment was installed over it and the floor was properly prepared I'm sure you would be okay installing Avaire tile over.
06-24-2009 10:52 AM
Avaire Archive Author: Jonathan
Date: 2/26/2009 1:48 pm EDT

I have heard of the WarmlyYours brand, but I do not have their technical specs. Perhaps I misunderstand, but if their pad is truly 3/8" (0.375") thick, I think that would be too thick for use under the Avaire system. The QuietWarmth brand product is 0.11" thick, or less than 1/3rd of a 3/8" pad.

Generally speaking, if the heating system is designed for use under laminate wood flooring, which cannot be exposed to temperatures more than 85F, it will be compatible with our system. One concern would be the wire thickness and composition. With QuietWarmth, the wires are attached to the pad which provides some protection. If a raw set of wires were installed directly under our tile over a rough concrete surface, over time I'd be concerned about the "grid" under our system "pinching" the heating wires and wearing through the wire insulation. With QuietWarmth, we don't have that concern because the pad protects the wires, and the wire composition is actually a fiber and not a metallic material.

I will review the WarmlyYours system to determine whether or not it is compatible with Avaire.

Thank you for considering Avaire and for your excellent question!

06-24-2009 10:51 AM
Avaire Archive Author: Jon
Date: 2/24/2009 11:06 pm EDT
Upon further research I have learned that the Environ II heat panels are acceptable to use with Quietwalk underlayment.

I assume then that, after installing underlayment under the Avaire tiles, the finished floor will be ok? It wont be to soft or unstable and will not affect the grout?
06-24-2009 10:51 AM
Avaire Archive Author: Jon
Date: 2/22/2009 7:51 pm EDT
Thank you Journeyman for your information, I think I will just install a wall heater for the added heat, and use rugs. I do not want to compromise the integrity of the tile.
06-24-2009 10:50 AM
Avaire Archive Author: Journeyman
Date: 2/21/2009 8:21 pm EDT
Not totally familiar with what pads are available for laminate floors. I think 1/8" is typical. But, the 3/8" you mentioned would be pretty thick for hard tile I think. The plastic trays (Avaire) may be the saving-grace in that scenario, just don't know for sure.
06-24-2009 10:50 AM
Avaire Archive Author: Jon
Date: 2/21/2009 6:37 pm EDT
I am not exactly sure, but is pad used under laminate flooring real thin, like 1/8"? They say it is used under laminate flooring as well as carpet.
06-24-2009 10:49 AM
Avaire Archive Author: Journeyman
Date: 2/21/2009 5:12 pm EDT

You should seek those guarantees from the WY people. I personally don't see how the grout would hold up under those circumstances. The Avaire grout is flexible only to a small degree. I would also be a little concerned about point-impacts to the tile over a soft pad such as the one you are suggesting. Point-loads from furniture legs may also be a concern under those circumstances.
This thread has more than 10 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 08:53 PM.

Powered by vBulletin® Version 3.8.2
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.

(888) 528-2473 Copyright © 2009 : CoMc, LLC All Rights Reserved. ~ Design by Chip Thompson